Page 1 Page 2 Page 3 Page 4 Page 5 Page 6 Page 7 Page 8 Page 9 Page 10 Page 11 Page 12 Page 13 Page 14 Page 15 Page 16 Page 17 Page 18 Page 19 Page 20 Page 21 Page 22 Page 23 Page 24 Page 25 Page 26 Page 27 Page 28 Page 29 Page 30 Page 31 Page 32 Page 33 Page 34 Page 35 Page 36 Page 37 Page 38 Page 39 Page 40 Page 41 Page 42 Page 43 Page 44 Page 45 Page 46 Page 47 Page 48 Page 49 Page 50 Page 51 Page 52 Page 53 Page 54 Page 55 Page 56 Page 57 Page 58 Page 59 Page 60 Page 61 Page 62 Page 63 Page 64 Page 65 Page 66 Page 67 Page 68 Page 69 Page 70 Page 71 Page 72 Page 73 Page 74 Page 75 Page 76 Page 77 Page 78 Page 79 Page 80 Page 81 Page 82 Page 83 Page 84 Page 85 Page 86 Page 87 Page 88 Page 89 Page 90 Page 91 Page 92 Page 93 Page 94 Page 95 Page 96 Page 97 Page 98 Page 99 Page 100 Page 101 Page 102 Page 103 Page 104 Page 105 Page 106 Page 107 Page 108 Page 109 Page 110 Page 111 Page 112 Page 113 Page 114 Page 115 Page 116 Page 117 Page 118 Page 119 Page 120 Page 121 Page 122 Page 123 Page 124 Page 125 Page 126 Page 127 Page 128 Page 129 Page 130 Page 131 Page 132 Page 133 Page 134 Page 135 Page 136 Page 137 Page 138 Page 139 Page 140 Page 141 Page 142 Page 143 Page 144 Page 145 Page 146 Page 147 Page 148 Page 149 Page 150 Page 151 Page 152 Page 153 Page 154 Page 155 Page 156 Page 157 Page 158 Page 159 Page 160 Page 161 Page 162 Page 163 Page 164 Page 165 Page 166 Page 167 Page 168 Page 169 Page 170 Page 171 Page 172 Page 173 Page 174 Page 175 Page 176 Page 177 Page 178 Page 179 Page 180 Page 181 Page 182in place. These qualitative measures are benchmarked and validated against sound petroleum reservoir engineering principles and equations to estimate the ultimate recoverable reserves volume. These techniques include, but are not limited to, nodal analysis, material balance, and numerical flow simulation. Internal controls over reserves estimation process In our Production and Development team, we maintain an internal staff of petroleum engineering and geoscience professionals with significant international experience that contribute to our internal reserve and resource estimates. This team works closely with our independent petroleum engineers to ensure the integrity, accuracy and timeliness of data furnished in their reserve and resource estimation process. Our Production and Development team is responsible for overseeing the preparation of our reserves estimates and has over 100 combined years of industry experience among them with positions of increasing responsibility in engineering and evaluations. Each member of our team holds a minimum of Bachelor of Science degree in petroleum engineering or geology. The RSC technical person primarily responsible for preparing the estimates set forth in the RSC reserves report incorporated herein is Mr. Guadalupe Ramirez. Mr. Ramirez has been practicing consulting petroleum engineering at RSC since 1981. Mr. Ramirez is a Licensed Professional Engineer in the State of Texas (No. 48318) and has over 35 years of practical experience in petroleum engineering. He graduated from Texas A&M University in 1976 with a Bachelor of Science Degree in Mechanical Engineering. Mr. Ramirez meets or exceeds the education, training, and experience requirements set forth in the Standards Pertaining to the Estimating and Auditing of Oil and Gas Reserves Information promulgated by the Society of Petroleum Engineers and is proficient in judiciously applying industry standard practices to engineering and geoscience evaluations as well as applying SEC and other industry reserves definitions and guidelines. The Audit Committee provides oversight on the processes utilized in the development of our internal reserve and resource estimates on an annual basis. In addition, our Production and Development team meets with representatives of our independent reserve engineers to review our assets and discuss methods and assumptions used in preparation of the reserve and resource estimates. Finally, our senior management review reserve and resource estimates on an annual basis. 27